Northlight's Isolated splitters offer full electrical and signal isolation.
Controlled slew rate drivers.
Home Page DMX to 0-10 VDC converter Convert 0-10VDC to DMX512 protocol. Isolated DMX splitter. DMX to PWM servo DMX512 AC light dimmer boards DMX512 DC PWM boards Misc items on sale Purchase online using PayPal Application circuits for Encoder and Decoder Notes about DMX 512 protocol Trouble shooting guide. Warranty and disclaimer.
  • DMXiso3 has DMX input,DMX thru and 3 isolated outputs.
  • 3 optically isolated outputs.
  • Each output has its own driver chip.
  • New!Controlled slew rate drivers.
  • Quality Neutrik, 5 pin XLR connector.
  • Dual power supply. No electrical connection between input and output.
  • UL listed, split bobbin transformer.
  • Has switch selectable terminator.
  • Specs comparable to higher cost splitters.Low cost, not cheap.
  • ABS case.Measures 4.25 X 4.25 X 2.25
  • Requires 120 VAC, standard duplex receptacle.
    		• 5 pin XLR
    5 pin XLR connector - $225.00.
    Sorry - out of stock.

    Download the manual in PDF format.
     Northlight systems isolated signal splitter for DMX 512 offers full electrical isolation between the input and 3 outputs. Each output has it’s own line driver and optical isolator.
    Controlled slew rate driver , decreasing the EMI radiated from the RS485 lines, and improving signal fidelity with misterminated lines.
     In addition to signal isolation, power isolation is achieved with a split bobbin transformer and separate power supplies for the input and output sections.
     The DMX splitter also serves as a repeater since each output drives up to 32 receivers.
     A non-isolated DMX thru is provided.

    Ease of use.
    No wall wart transformer to lose. No adjustments at all. A good splitter is transparent to the system and the user.

    LED indicator
    Red LED’s for power supplies A and B.
    Green LED indicates input signal present.

    Connectors
    DMX Input: Male XLR, 5 pin
    DMX thru: Female XLR, 5 pin
    DMX out: Female XLR, 5 pin

    Power
    Standard 3 prong polarized cord for 120 volt duplex receptacles.

    Specs
    All specifications meet or exceed requirements

    Baud rate:  0 to 1000 KB
    Input circuit:  EIA-485 compatible receiver
    Input signal:    0.2 volts minimum, 12 volts maximum
    Output circuit: Fast, 2500 volt optical isolators
    EIA-485 compatible drivers
    Connectors:      5 pin XLR
    Power Isolation: 1500 volt split bobbin, UL listed transformer
    Power input:    110 - 120 volts, 60 hertz, 2 amps
    Case:     Thermoplastic, Black.
    Dimensions:      3 output,5 pin XLR: 6" deep, 1.6" high, 5.6" wide

    Features:
    Outputs are isolated from each other.
    Outputs are separately buffered.
    Each output drives up to 32 receivers.
    Signal problems on one output cannot affect another output.
    No user adjustments.
    Input is electrically isolated from the outputs. Devices are protected from failure at either end.
    All integrated circuits are socketed for easy repair.
    Uses 2500 volt optical couplers.
    Reliable, high speed data throughput.
    Power and input signal indicators

    Termination:
     Northlights splitter contains a switch selectable terminating resistor. When the “DMX thru” connector is used, the splitter is not the last device on the link, the terminator switch should be set to "out". If the splitter is the last receiver on the link, then a terminator switch should be set to "in".

    Send  To NorthlightSystems@att.net.
    		Made in the USA.